[     1.000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
[     1.000000]     2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013,
[     1.000000]     2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023,
[     1.000000]     2024, 2025
[     1.000000]     The NetBSD Foundation, Inc.  All rights reserved.
[     1.000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[     1.000000]     The Regents of the University of California.  All rights reserved.

[     1.000000] NetBSD 10.99.14 (GUPPY) #2: Tue Jul 15 12:22:46 EEST 2025
[     1.000000] 	gson@gumbo:/prod/g5/macppc/obj/sys/arch/macppc/compile/GUPPY
[     1.000000] total memory = 2048 MB
[     1.000000] oea_startup: failed to allocate DEAD ZONE: error=12
[     1.000000] avail memory = 1959 MB
[     1.000000] timecounter: Timecounters tick every 10.000 msec
[     1.000000] found openpic PIC at 80040000
[     1.000000] OpenPIC Version 1.2: Supports 4 CPUs and 120 interrupt sources.
[     1.000000] bootpath: /ht/pci@3/ata-6/disk@0:0/netbsd.
[     1.000000] mainbus0 (root)
[     1.000000] cpu0 at mainbus0: 970 (Revision 2.2), ID 0 (primary)
[     1.000000] cpu0: HID0 0x513081<NAP,DPM,NHR,TBCTRL,EXTBEN,ENATTN> 0x80000000<EMCP>, powersave: 1
[     1.000000] memory0 at mainbus0: len=512
[     1.000000] spdmem0 at memory0
[     1.000000] spdmem0: DDR SDRAM, no parity or ECC, 512MB, 400MHz (PC-3200)
[     1.000000] spdmem0: 13 rows, 10 cols, 2 ranks, 4 banks/chip, 5.0ns cycle time
[     1.000000] spdmem0: tAA-tRCD-tRP-tRAS: 2-3-3-8
[     1.000000] spdmem0: voltage SSTL 2.5V, refresh time 7.8us (self-refreshing)
[     1.000000] spdmem1 at memory0
[     1.000000] spdmem1: DDR SDRAM, no parity or ECC, 512MB, 400MHz (PC-3200)
[     1.000000] spdmem1: 13 rows, 10 cols, 2 ranks, 4 banks/chip, 5.0ns cycle time
[     1.000000] spdmem1: tAA-tRCD-tRP-tRAS: 2-3-3-8
[     1.000000] spdmem1: voltage SSTL 2.5V, refresh time 7.8us (self-refreshing)
[     1.000000] spdmem2 at memory0
[     1.000000] spdmem2: DDR SDRAM, no parity or ECC, 512MB, 400MHz (PC-3200)
[     1.000000] spdmem2: 13 rows, 10 cols, 2 ranks, 4 banks/chip, 5.0ns cycle time
[     1.000000] spdmem2: tAA-tRCD-tRP-tRAS: 2-3-3-8
[     1.000000] spdmem2: voltage SSTL 2.5V, refresh time 7.8us (self-refreshing)
[     1.000000] spdmem3 at memory0
[     1.000000] spdmem3: DDR SDRAM, no parity or ECC, 512MB, 400MHz (PC-3200)
[     1.000000] spdmem3: 13 rows, 10 cols, 2 ranks, 4 banks/chip, 5.0ns cycle time
[     1.000000] spdmem3: tAA-tRCD-tRP-tRAS: 2-3-3-8
[     1.000000] spdmem3: voltage SSTL 2.5V, refresh time 7.8us (self-refreshing)
[     1.000000] uni_n0 at mainbus0 address 0xf8000000
[     1.000000] uni_n0: found EEPROM data for CPU 0
[     1.000000] uni_n0: found EEPROM data for CPU 1
[     1.000000] ki2c0 at uni_n0 address 0xf8001000
[     1.000000] iic0 at ki2c0: I2C bus
[     1.000000] lmtemp0 at iic0 addr 0x4a: temp-monitor DS75 Temperature Sensor
[     1.000000] admtemp0 at iic0 addr 0x4c: MAX6690 temperature sensor: id. 0x4d, rev. 0x09
[     1.000000] admtemp1 at iic0 addr 0x4e: MAX6690 temperature sensor: id. 0x4d, rev. 0x09
[     1.000000] i2c-hwclock (cy28508) at iic0 addr 0x69 not configured
[     1.000000] i2c-hwclock (cy2213) at iic0 addr 0x65 not configured
[     1.000000] fcu0 at iic0 addr 0xaf: Fan Control Unit
[     1.000000] i2c-cpu-voltage (pca9556) at iic0 addr 0x18 not configured
[     1.000000] adadc0 at iic0 addr 0x2c: AD7417
[     1.000000] cpuid (24256) at iic0 addr 0x50 not configured
[     1.000000] i2c-cpu-voltage (pca9556) at iic0 addr 0x19 not configured
[     1.000000] adadc1 at iic0 addr 0x2d: AD7417
[     1.000000] cpuid (24256) at iic0 addr 0x51 not configured
[     1.000000] cereal (cereal) at iic0 addr 0xe0 not configured
[     1.000000] uninorth0 at mainbus0
[     1.000000] pci0 at uninorth0 bus 0
[     1.000000] pci0: i/o space, memory space enabled
[     1.000000] pchb0 at pci0 dev 11 function 0
[     1.000000] pchb0: vendor 106b product 004b (rev. 0x00)
[     1.000000] genfb0 at pci0 dev 16 function 0: vendor 10de product 0321 (rev. 0xa1)
[     1.000000] genfb0: framebuffer at 0x98004000, size 1920x1200, depth 8, stride 2048
[     1.000000] no data for est. mode 640x480x67
[     1.000000] -- genfb_init_palette depth 8
[     1.000000] -- returningwsdisplay0 at genfb0 kbdmux 1-- attached tty 262143
[     1.000000] : console (default, vt100 emulation)
[     1.000000] wsmux1: connecting to wsdisplay0
[     1.000000] drm at genfb0 not configured
[     1.000000] ibmcpc0 at mainbus0
[     1.000000] Mapping in config space @ pa 0xf2000000, size: 0x02800000
[     1.000000] pci1 at ibmcpc0 bus 1
[     1.000000] pci1: i/o space, memory space enabled
[     1.000000] obio0 at pci1 dev 7 function 0: addr 0x80000000
[     1.000000] zsc0 at obio0 irq 22,23
[     1.000000] zstty0 at zsc0 channel 0
[     1.000000] -- attached tty 0
[     1.000000] zstty1 at zsc0 channel 1
[     1.000000] -- attached tty 1
[     1.000000] ki2c1 at obio0
[     1.000000] iic1 at ki2c1: I2C bus
[     1.000000] cereal (cereal) at iic1 addr 0xe0 not configured
[     1.000000] deq0 at iic1 addr 0x35 Audio Codec (tas3004)
[     1.000000] snapper0 at obio0 offset 0x10000: irq 30,1,2
[     1.000000] pmu0 at obio0 offset 0x16000 irq 25:  rev. 12
[     1.000000] pmu0: initializing IIC bus
[     1.000000] iic2 at pmu0: I2C bus
[     1.000000] pmu0: initializing RTC
[     1.000000] pmu0: power-mgt not configured
[     1.000000] obiofan0 at obio0 offset 0x4c
[     1.000000] model PowerMac7,3
[     1.000000] snapper0: codec: TAS3004
[     1.000000] audio0 at snapper0: playback, capture, full duplex
[     1.000000] audio0: slinear_be:16 -> slinear_be:16 2ch 48000Hz, blk 12288 bytes (64ms) for playback
[     1.000000] audio0: slinear_be:16 <- slinear_be:16 2ch 48000Hz, blk 12288 bytes (64ms) for recording
[     1.000000] spkr0 at audio0: PC Speaker (synthesized)
[     1.000000] wsbell0 at spkr0 mux 1
[     1.000000] ohci0 at pci1 dev 8 function 0: vendor 106b product 0040 (rev. 0x00)
[     1.000000] ohci0: interrupting at irq 27
[     1.000000] ohci0: OHCI version 1.0, legacy support
[     1.000000] usb0 at ohci0: USB revision 1.0
[     1.000000] ohci1 at pci1 dev 9 function 0: vendor 106b product 0040 (rev. 0x00)
[     1.000000] ohci1: interrupting at irq 28
[     1.000000] ohci1: OHCI version 1.0, legacy support
[     1.000000] usb1 at ohci1: USB revision 1.0
[     1.000000] pci2 at ibmcpc0 bus 5
[     1.000000] pci2: i/o space, memory space enabled
[     1.000000] puc0 at pci2 dev 2 function 0: NetMos NM9865 1 UART (com)
[     1.000000] com0 at puc0 port 0 (16550-compatible): interrupting at irq 52
[     1.000000] com0: ns16550a, 16-byte FIFO
[     1.000000] -- attached tty 262143
[     1.000000] puc1 at pci2 dev 2 function 1: NetMos NM9865 1 UART (com)
[     1.000000] com1 at puc1 port 0 (16550-compatible): interrupting at irq 52
[     1.000000] com1: ns16550a, 16-byte FIFO
[     1.000000] -- attached tty 262143
[     1.000000] puc2 at pci2 dev 2 function 2: NetMos NM9865 Single LPT (lpt)
[     1.000000] lpt0 at puc2 port 0: interrupting at irq 52
[     1.000000] ohci2 at pci2 dev 11 function 0: vendor 1033 product 0035 (rev. 0x43)
[     1.000000] ohci2: interrupting at irq 63
[     1.000000] ohci2: OHCI version 1.0
[     1.000000] usb2 at ohci2: USB revision 1.0
[     1.000000] ohci3 at pci2 dev 11 function 1: vendor 1033 product 0035 (rev. 0x43)
[     1.000000] ohci3: interrupting at irq 63
[     1.000000] ohci3: OHCI version 1.0
[     1.000000] usb3 at ohci3: USB revision 1.0
[     1.000000] ehci0 at pci2 dev 11 function 2: vendor 1033 product 00e0 (rev. 0x04)
[     1.000000] ehci0: 32-bit DMA
[     1.000000] ehci0: interrupting at irq 63
[     1.000000] ehci0: EHCI version 1.0
[     1.000000] ehci0: 2 companion controllers, 3 ports each: ohci2 ohci3
[     1.000000] usb4 at ehci0: USB revision 2.0
[     1.000000] pci3 at ibmcpc0 bus 2
[     1.000000] pci3: i/o space, memory space enabled
[     1.000000] wdc0 at pci3 dev 13 function 0: interrupting at irq 39
[     1.000000] atabus0 at wdc0 channel 0
[     1.000000] vendor 106b product 0042 (IEEE1394 serial bus, OpenHCI) at pci3 dev 14 function 0 not configured
[     1.000000] pci4 at ibmcpc0 bus 3
[     1.000000] pci4: i/o space, memory space enabled
[     1.000000] gem0 at pci4 dev 15 function 0: vendor 106b product 004c (rev. 0x00)
[     1.000000] gem0: interrupting at irq 41
[     1.000000] brgphy0 at gem0 phy 1: BCM54K2 1000BASE-T media interface, rev. 0
[     1.000000] brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
[     1.000000] gem0: Ethernet address 00:0d:93:33:6b:10, 10KB RX fifo, 4KB TX fifo
[     1.000000] pci5 at ibmcpc0 bus 4
[     1.000000] pci5: i/o space, memory space enabled
[     1.000000] svwsata0 at pci5 dev 12 function 0: ServerWorks K2 SATA Controller (rev. 0x00)
[     1.000000] svwsata0: bus-master DMA support present
[     1.000000] svwsata0: using irq 0 for native-PCI interrupt
[     1.000000] svwsata0: primary channel wired to native-PCI mode
[     1.000000] atabus1 at svwsata0 channel 0
[     1.000000] svwsata0: secondary channel wired to native-PCI mode
[     1.000000] atabus2 at svwsata0 channel 1
[     1.000000] svwsata0: secondary channel wired to compatibility mode
[     1.000000] atabus3 at svwsata0 channel 2
[     1.000000] svwsata0: secondary channel configured to compatibility mode
[     1.000000] atabus4 at svwsata0 channel 3
[     1.000000] svwsata1 at pci5 dev 12 function 1: ServerWorks K2 SATA Controller (rev. 0x00)

[     1.000000] vmmask 64fe0000 schedmask 7ffe0000 highmask 7ffe0000
[     1.000000] WARNING: system needs entropy for security; see entropy(7)
[     1.000000] timecounter: Timecounter "mftb" frequency 33333333 Hz quality 100
[     1.000003] timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
[     1.099995] uhub0 at usb0: NetBSD (0x0000) OHCI root hub (0x0000), class 9/0, rev 1.00/1.00, addr 1
[     1.099995] uhub0: 2 ports with 2 removable, self powered
[     1.099995] uhub1 at usb1: NetBSD (0x0000) OHCI root hub (0x0000), class 9/0, rev 1.00/1.00, addr 1
[     1.099995] uhub1: 2 ports with 2 removable, self powered
[     1.099995] uhub2 at usb2: NetBSD (0x0000) OHCI root hub (0x0000), class 9/0, rev 1.00/1.00, addr 1
[     1.099995] uhub2: 3 ports with 3 removable, self powered
[     1.099995] uhub3 at usb3: NetBSD (0x0000) OHCI root hub (0x0000), class 9/0, rev 1.00/1.00, addr 1
[     1.099995] uhub3: 2 ports with 2 removable, self powered
[     1.099995] uhub4 at usb4: NetBSD (0x0000) EHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 1
[     1.099995] uhub4: 5 ports with 5 removable, self powered
[     1.339993] atapibus0 at atabus0: 2 targets
[     1.390018] svwsata0 port 0: device present, speed: 1.5Gb/s
[     1.440008] cd0 at atapibus0 drive 0: <HL-DT-ST DVD-RW GWA-4082B, K29496G1507, C03D> cdrom removable
[     1.440008] cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
[     1.490008] cd0(wdc0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66) (using DMA)
[     1.539993] wd0 at atabus1 drive 0
[     1.539993] wd0: <Samsung SSD 850 EVO 250GB>
[     1.539993] wd0: drive supports 1-sector PIO transfers, LBA48 addressing
[     1.539993] wd0: 232 GB, 484521 cyl, 16 head, 63 sec, 512 bytes/sect x 488397168 sectors
[     1.670038] wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133), WRITE DMA FUA, NCQ (32 tags)
[     1.670038] wd0(svwsata0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA), WRITE DMA FUA EXT
[     1.719993] ehci0: handing over full speed device on port 1 to ohci2
[     2.379993] ehci0: handing over full speed device on port 3 to ohci2
[     2.689994] svwsata0 port 1: PHY offline
[     2.689994] svwsata0 port 2: PHY offline
[     2.689994] svwsata0 port 3: PHY offline
[     2.929995] ualea0 at uhub2 port 1 configuration 1 interface 0
[     2.929995] ualea0: Araneus (0x12d8) Alea I (0x0001), rev 2.00/1.56, addr 2
[     3.020029] entropy: ready
[     3.769997] umass0 at uhub4 port 4 configuration 1 interface 0
[     3.769997] umass0: Kingston (0x0951) DataTraveler 3.0 (0x1666), rev 2.10/1.10, addr 2
[     3.769997] umass0: using SCSI over Bulk-Only
[     3.769997] scsibus0 at umass0: 2 targets, 1 lun per target
[     3.769997] sd0 at scsibus0 target 0 lun 0: <Kingston, DataTraveler 3.0, PMAP> disk removable
[     3.769997] sd0: fabricating a geometry
[     3.769997] sd0: 59136 MB, 59136 cyl, 64 head, 32 sec, 512 bytes/sect x 121110528 sectors
[     4.040089] sd0: fabricating a geometry
[     4.209996] uhub5 at uhub2 port 2: Lite-On Tech (0x04b3) USB 1.1 2 port downstream low-power hub (0x3016), class 9/0, rev 1.10/2.01, addr 3
[     4.260014] uhub5: 4 ports with 2 removable, bus powered
[     5.199996] uhidev0 at uhub5 port 3 configuration 1 interface 0
[     5.199996] uhidev0: Lite-On Tech (0x04b3) IBM USB Travel Keyboard with UltraNav (0x3019), rev 1.10/1.16, addr 4, iclass 3/1
[     5.300031] ukbd0 at uhidev0
[     5.300031] wskbd0 at ukbd0: console keyboard, using wsdisplay0
[     5.300031] uhidev1 at uhub5 port 3 configuration 1 interface 1
[     5.300031] uhidev1: Lite-On Tech (0x04b3) IBM USB Travel Keyboard with UltraNav (0x3019), rev 1.10/1.16, addr 4, iclass 3/0
[     5.480053] uhidev1: 3 report ids
[     5.480053] uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0
[     5.480053] uhid1 at uhidev1 reportid 3: input=3, output=0, feature=0
[     6.049996] uhidev2 at uhub5 port 4 configuration 1 interface 0
[     6.049996] uhidev2: Synaptics Inc. (0x06cb) Composite TouchPad / TrackPoint (0x0009), rev 1.10/0.20, addr 5, iclass 3/1
[     6.150030] ums0 at uhidev2: 3 buttons
[     6.150030] wsmouse0 at ums0 mux 0
[     6.150030] uhidev3 at uhub5 port 4 configuration 1 interface 1
[     6.150030] uhidev3: Synaptics Inc. (0x06cb) Composite TouchPad / TrackPoint (0x0009), rev 1.10/0.20, addr 5, iclass 3/1
[     6.150030] ums1 at uhidev3: 3 buttons
[     6.150030] wsmouse1 at ums1 mux 0
[     6.150030] boot device: <unknown>
[     6.150030] root on wd0a dumps on wd0b
[     6.529998] kern.module.path=/stand/macppc/10.99.14/modules
[     6.529998] WARNING: clock gained 6 days
[     7.700000] com0: autoconfiguration error: com_iflush timeout 7f
[     7.700000] com0: autoconfiguration error: com_iflush timeout 0c
[     7.700000] com0: autoconfiguration error: com_iflush timeout 0c
[     7.700000] com0: autoconfiguration error: com_iflush timeout 0c
[     7.700000] com0: autoconfiguration error: com_iflush timeout 0c
[     7.700000] com1: autoconfiguration error: com_iflush timeout 93
[     7.700000] com1: autoconfiguration error: com_iflush timeout 0c
[     7.700000] com1: autoconfiguration error: com_iflush timeout 0c
[     7.700000] com1: autoconfiguration error: com_iflush timeout 0c
[     7.700000] com1: autoconfiguration error: com_iflush timeout 0c
[    36.290023] com0: autoconfiguration error: com_iflush timeout 0c
[    36.290023] com0: autoconfiguration error: com_iflush timeout 0c
[    36.290023] com0: autoconfiguration error: com_iflush timeout 0c
[    36.290023] com1: autoconfiguration error: com_iflush timeout 0c
[    36.290023] com1: autoconfiguration error: com_iflush timeout 0c
[    36.290023] com1: autoconfiguration error: com_iflush timeout 0c
[    78.030050] -- attached tty 262143